P.O. Box 75986, Manurewa, Auckland     New Zealand
PH: 64 9 269 0710  FAX: 64 9269 4140
Email: info@pacificurethanes.co.nz


ABOUT US          PRODUCT RANGE     RESPONSE FORM  

2 COMPONENT FOAM KITS

 

 

Touch 'n Seal

Technical data

User Guide

Trouble shooting

Two-Component Polyurethane Foam Sealant


Foam Kit 15

Two-Component Polyurethane Foam Sealant
Foam Kit 200

 

Two Component Foam Insulation
Foam Kit 600

 

 

 

Foam Insulation

 

  

 

FOAM KITS - Disposable Polyurethane Foam Systems

Please ensure full understanding of operating instructions before usage. Temperature is critical to efficiency of Kits

 
Touch ‘n Seal two-component, polyurethane foam systems are designed for use in commercial sealing, insulating, patching, and filling applications. The high closed cell content of the cured foam makes it suitable as a general sealant to prevent air leakage in cold storage and other insulating/sealing applications. Two-component polyurethane foam systems provide fast, even foam flow that cures in 1 minute, making it ideal for vertical applications.

 

• Self-contained
• Portable, disposable
• Foam expands 30 times
• Spray applied, dries in 1 minute
• Variety of sizes (15 - 200 board feet)
• Standard or flame-retardant formulas
• No CFC's
• No urea formaldehyde
• Single box units have pre-connected hoses
 

NON-FR FOAM
• Density ASTM D-1622: 1.75 ± 0.2 pcf
• K-Factor ASTM C-177: 0.144
• R-Factor ASTM C-177: 6.9/in.
• Compressive Strength ASTM D-1621:
     10%, parallel: 19psi
     10%, perpendicular: 13.4psi
• Tensile Strength ASTM D-1623:
      parallel: 34psi
      perpendicular: 24.1psi
• Dimensional Stability ASTM D-2126:
     -40°F, 2-wks: = .88%, vol. change
     158°F, 100% RH 2-wks: + 14% vol. change
• Water absorption ASTM D-2842: 1-3.5%
• Closed Cell Content ASTM D-2856: 90%, min.
• Shelf Life: 18 months -1 Month after opening, short   spray every week if not using product regularly.
Product Board Feet Cubic Feet Cubic Meters Board Meters*
U2-200 200 16.67 .47 5.66
U2-600 600 50.00 1.400 16.99
 

PROPER STORAGE & APPLICATION REMINDERS FOR ALL 2-COMPONENT POLYURETHANE FOAMS

 


STORAGE REMINDERS
Materials may be stored below 70°F. However, temperatures of A & B canister materials must be brought to a minimum of 70°F prior to application. Canisters stored in low temperatures may require more than 24 hours to warm their chemical contents.

APPLICATION REMINDERS
For optimum performance and foam quality, the temperature of the spray environment and foam materials should be 70-80°F. Application in temperatures below 70°F may increase set up time and reduce overall performance of polyurethane foam.

WARRANTY AGAINST PRODUCT PERFORMANCE/FAILURE
Please read carefully and adhere strictly to the operating instructions, warnings and cautions contained in or affixed to this product. Failure to follow all instructions, directions, warnings, and cautions shall release Convenience Products from any and all liability. Representatives, distributors and dealers of this product may make no claims or warranties not herein expressed.
 

 

P.O. Box 75986, Manurewa, Auckland, New Zealand
PH: 64 9 269 0710  FAX: 64 9269 4140
Email: info@pacificurethanes.co.n